This report is an outcome of a master degree project at Linköpings University in co-operation with Micronic Laser Systems AB. The purpose with this master degree project was to investigate how to implement a receiver in a data transfer system. The system consists of several data channels, where every channel consists of three parts: driver, transmission lines and receiver. The driver send low amplitude differential signals via the transmission lines to the receiver that amplifies and converts it to a single-ended signal. The receiver has to be fast and be able to feed an output signal with high voltage swing.

This report present the design and manufacturing of a wide-band driver amplifier placed in radar module for airborne applications. The major goals for the amplifier were a high efficiency and to deliver a predefined output power. To reach the second goal an additional preamplifier had to be constructed. The amplifiers were constructed in three steps: Design and Layout in the software Microwave Office, Mounting components and Verification. The driver amplifier was decided to be a push pull configuration consisting of two parallel transistors biased in class AB.

Softube has developed DSP-card and software for simulation of the sound of old tube amplifiers. The purpose with this thesis is to design a compact amplifier with high power to function together with the DSP-card and build a unit that can replace several other guitar amplifiers. The advantages with that kind of solution could be that it would be cheaper, easier to carry and easier to stor than the real amplifiers. The amplifier that has been designed is of class D type with digital PWM modulator. There is several types of amplifier modules on the market that use analog input signal, but if one of them would be used a D-A converter is needed on the DSP card.

The last few decades the development in the field of electronics has been huge. The components performance gets better at the same time as the manufacturing cost decreases. Many of the design moments that have to be done, are done automatically today, but it can get better. Especially for analog circuit design.At Electronic System in Linköpings universitet, research is in progress to develop a tool that can design analog circuits in reasonable time. It means that it has to size the components (transistors, resistances, capacitances etc), so that the circuit can fulfill the performance requirements.

This paper describes a method for wireless energy transfer via near-field electromagnetic inductionthat is inexpensive, simple and can be applied to almost any type of system, regardless of size andenergy demands.The method uses a primary unit consisting of an oscillator, amplifier and inductive coil thattransfers energy to a secondary unit consisting of a coil, rectifier and voltage regulator. Two typesof oscillators and several amplifier designs were realized and evaluated together with a multitudeof flat coils of both monofilar and bifilar type.The results show that it is important to use an oscillator whose frequency is dependent on theinductance of the connected transmission coil, such as the Colpitts oscillator. This is preferable toan oscillator with a preset frequency, such as a Schmitt-trigger oscillator..

Normally the operational amplifier is used as a component in active filter design. The goal for future components in filter design is large bandwith and the use of low supply voltages. The use of current-mode instead of voltage-mode circuits gets a step closer to the required performance. A component that use current as the signal conveying part is the current conveyor. In this report a comparative study between two current conveyor structures of second generation (CCII) is performed.

This master thesis deals with problems in the arc length control in Pulsed MIG/MAG Welding. The main problem is that it is not possible to measure the arc length. In the present solution the voltage over both the electrode and the arc represents the arc length. To improve the arc length control a model of the electrode melting has been built. One output from the model is the voltage over the electrode and with this voltage together with the measured voltage it is possible to calculate the voltage over just the arc.

The purpose with the report is to show that it is possible to design a class-D amplifier, using a programmable FPGA mounted on a developing card from Xess and a H-bridge. The FPGA was programmed in VHDL which is the language the software from Xilinx use to implement a logical function into the FPGA The logical function corresponds to a modeling of the music signal and the modeling can be described as a comparator which compare the music signal with a triangle wave and as a out signal produce a pulse width modulated (PWM) signal. The report is also a review and evaluating of two different modulating technologies, AD- modeling and BD-modeling. A detailed part about how the H-bridge was designed and how it works. The result of this project is a working audio amplifier to a significant lower price than the products in todays market..

A current conveyor is an active building block that can be used to implement most active and passive components. It differs from the operation amplifier in that it uses current instead of voltage. The current conveyor also has significantly higher voltage gain over a broader frequency range. To simplify the construction of analogue circuits and increase the construction efficiency it is desirable to use a top-down methodology. This means that the whole system is partitioned into a hierarchy of subsystems.

This paper describes a method for wireless energy transfer via near-field electromagnetic inductionthat is inexpensive, simple and can be applied to almost any type of system, regardless of size andenergy demands.The method uses a primary unit consisting of an oscillator, amplifier and inductive coil thattransfers energy to a secondary unit consisting of a coil, rectifier and voltage regulator. Two typesof oscillators and several amplifier designs were realized and evaluated together with a multitudeof flat coils of both monofilar and bifilar type.The results show that it is important to use an oscillator whose frequency is dependent on theinductance of the connected transmission coil, such as the Colpitts oscillator. This is preferable toan oscillator with a preset frequency, such as a Schmitt-trigger oscillator..

Voltage sag indices are a way of quantifying the performance of the power supply, as far as voltage sags are concerned. Indices can be defined for individual events, for individual sites, and for a whole system. A standard method for single-event methods is part of IEC standard 61000-4-30.This thesis emphasizes the importance of voltage sag indices and different methods for calculating three-phase voltage sag characteristics. Three-phase events measured in a medium network voltage over period of one month were analyzed, results examined and statistically evaluated. An algorithm for calculating voltage sag characteristics and indices was created in Matlab.

Voltage sag indices are a way of quantifying the performance of the power supply, as far as voltage sags are concerned. Indices can be defined for individual events, for individual sites, and for a whole system. A standard method for single-event methods is part of IEC standard 61000-4-30.This thesis emphasizes the importance of voltage sag indices and different methods for calculating three-phase voltage sag characteristics. Three-phase events measured in a medium network voltage over period of one month were analyzed, results examined and statistically evaluated. An algorithm for calculating voltage sag characteristics and indices was created in Matlab.

Voltage sag indices are a way of quantifying the performance of the power supply, as far as voltage sags are concerned. Indices can be defined for individual events, for individual sites, and for a whole system. A standard method for single-event methods is part of IEC standard 61000-4-30.This thesis emphasizes the importance of voltage sag indices and different methods for calculating three-phase voltage sag characteristics. Three-phase events measured in a medium network voltage over period of one month were analyzed, results examined and statistically evaluated. An algorithm for calculating voltage sag characteristics and indices was created in Matlab.

Voltage sag indices are a way of quantifying the performance of the power supply, as far as voltage sags are concerned. Indices can be defined for individual events, for individual sites, and for a whole system. A standard method for single-event methods is part of IEC standard 61000-4-30.This thesis emphasizes the importance of voltage sag indices and different methods for calculating three-phase voltage sag characteristics. Three-phase events measured in a medium network voltage over period of one month were analyzed, results examined and statistically evaluated. An algorithm for calculating voltage sag characteristics and indices was created in Matlab.

Voltage sag indices are a way of quantifying the performance of the power supply, as far as voltage sags are concerned. Indices can be defined for individual events, for individual sites, and for a whole system. A standard method for single-event methods is part of IEC standard 61000-4-30.This thesis emphasizes the importance of voltage sag indices and different methods for calculating three-phase voltage sag characteristics. Three-phase events measured in a medium network voltage over period of one month were analyzed, results examined and statistically evaluated. An algorithm for calculating voltage sag characteristics and indices was created in Matlab.